Napco Security Technologies GEM-DXRP2 Manuel d'utilisateur Page 25
- Page / 36
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
25
PROGRAMMING (OPTIONAL)
Introduction
The Program Mode (optional) is used to
customize User Codes. Access to the
Program Mode requires a special User
Code, therefore not all users may have
the ability to program.
Notes:
1. If the system contains more than one
keypad, only the keypad designated
“No. 1” may be used for programming
(if in doubt which is No. 1, ask your
installer).
2. Operation of the keypad buttons in
the Program Mode is different from
that for normal operation. Refer to the
accompanying diagram for keypad
functions in the Program Mode.
3. If the selected function requires more
than one screen, scroll the display
using
A.
4. While in the Program Mode, the
ARMED and STATUS lights remain
off and burglar and fire alarm func-
tions are disabled.
5. If the keypad detects no activity in the
Program Mode for more than 4 min-
utes, a tone will sound; to silence the
tone, press the blue
G button.
6. The programmed code or description
will not be permanently stored until
you press
D.
7. To exit the Program Mode, press
C.
Programming User Codes
Do not attempt to program a code contain-
ing any blank spaces between digits. In
selecting your codes, do not program re-
petitive numbers (1111), consecutive
numbers (1234), your birth date, address,
or other obvious combinations. Choose a
code of up to six digits (a minimum of four
is recommended, and required in UL in-
stallations). NOTE: Duplicate Codes are
not allowed; therefore a duplicate Code en-
tered in the LCD Window will erase when
D is pressed.
The User Program Mode is accessed from
the Function Mode as follows:
1. Enter your code, then press
A to
enter Function Mode.
2. Answer NO (press
F) until
"TurnOn Prog Yes/No" is displayed,
then press the YES button (
E).
"User01" will display.
Note: If you pass "TurnOn Prog", press
B to scroll back.
3. Using the number buttons, enter a
User Number as a two-digit number
(enter 1-9 as "01" - "09").
4. Press A. The cursor will advance
to the User Code screen and read the
existing code, if any.
(continued)
- OPERATING GUIDE for your 1
- INTRODUCTION 2
- TABLE OF CONTENTS 3
- G button to signal an 5
- 7 and the G 5
- 8 and the G 5
- 9 and the G 5
- ZONES FAULTED 6
- 02 BACK DOOR 6
- BYPASSED 6
- 02 BACK DOOR 6
- C, then arm the panel. A 3 7
- C and the system trou 7
- Area Arming (Optional) 8
- YES NO) 9
- Instant Protection 10
- Disarming the System 11
- To silence an audible alarm: 11
- 991234J 12
- FIRE PROTECTION 13
- KEYPAD FUNCTIONS 17
- CENTRAL STATION MONITORING 22
- ADVANCED FEATURES 23
- PROGRAMMING (OPTIONAL) 25
- User 01 26
- KEYPAD MESSAGES 28
- GLOSSARY 32
- SYSTEM TROUBLE ERROR CODES 35
- NAPCO LIMITED WARRANTY 36
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Napco Security Technologies GEM-DXRP2
Systèmes de contrôle d'accès de sécurité Napco Security Technologies XP-400 Manuel d'utilisateur
(28 pages)
(28 pages)
Systèmes de contrôle d'accès de sécurité Napco Security Technologies GEM-DXK3 Manuel d'utilisateur
(32 pages)
(32 pages)
SilberSonne TS40CWW manuels
Manuels d'utilisation et guides de l'utilisateur pour Bandes LED SilberSonne TS40CWW.
Nous fournissons des manuels en pdf 1 SilberSonne TS40CWW à télécharger gratuitement par type de document : Fiche technique
Commentaires sur ces manuels